BG-GRIND4 4PCS Set Complete Grinding Jig System for Wood Chisels
$119.99
Product Description
Components
This high-performance grinding jig serves as an upgraded grinder table for everyday grinding. It includes the platform table, long support arm,fingernail gouge jig and skew jig attachment.
Platform Table
The Platform can be used to sharpen scrapers, parting tools, flat or straight edge skews as well as standard wood chisels.
Long Support arm
The Long Support arm can be used to grind standard (flat grind) bowl gouges and roughing gouges.
They are both ground with the same technique.
Fingernail Gouge Jig
The Fingernail Gouge Jig will consistently produce repeatable geometries on turning tools such as fingernail and spindle gouges.
Skew Jig Attachment
The Skew Jig attachment will perform the skew angle grinding on flat and curved skews and scrapers.
Step 1. Setting up the Grinding Jig on Grinders
It is important that the position of the wheel and the jig are fixed in relation to each other, to get repeatable results.The Base Clamps must be mounted under the grinding wheels with the center of the grinding wheel in line with the center of the clamp. 
Step 2. Setting up the Grinding Jig on Grinders
The front of the base clamp should be aligned with the front edge of the grinding wheel. 
Step 3. Setting up the Grinding Jig on Grinders
The bottom of the base clamp must be mounted between 160 and 165mm below the center line of the grinding wheel.For smaller grinders, it may be necessary to mount the grinder on a second piece of board to raise the height.
OPERATION Using the Platform
1. With the grinder turned off slide the assembled platform into the base on either side of the grinder.
2. Lock the platform arm in place using the cam lock lever on the base clamp.
3. Adjust the platform so that the tool meets the wheel at the required angle then adjust the platform arm to ensure the gap between the platform and wheel is at its minimum.
OPERATION Using the Long Support Arm
1. Slide it in or out of the base clamp until the bevel of your gouge lays flat on your wheel surface when viewed from the side. Lift the edge of the chisel off the wheel and turn the grinder on.
2. Gently lower the gouge onto the wheel and allow the grinder to make a small mark on your chisel.
3. Lift the chisel completely and inspect the grind mark on the bevel.
4. Sharpen the gouge by touching the tool and rolling slowly to either side keeping the tool moving.
OPERATION Using the Fingernail Gouge Jig
1. Insert the tool into the jig so that 50mm is protruding from the front.
2. Set the center bevel angle by moving the Long Support arm as required.
3. Once the position is set correctly, sharpen the gouge by touching the tool on the wheel and rolling the whole jig slowly to either side keeping the tool moving to prevent excessive heat build up.
OPERATION Using the Skew Jig Attachment
1. Place the Skew Jig attachment over the end of the Long Arm support and hold in place by tightening the round knob.
2. Set the correct angle in the same way as the standard gouge by adjusting the Long Support arm. You can flip the tool over to repeat the grind on the opposite side.
Model comparison
Add to Cart
Add to Cart
Add to Cart
Add to Cart
Customer Reviews
4.6 out of 5 stars 37
4.6 out of 5 stars 37
4.6 out of 5 stars 37
4.6 out of 5 stars 37
Price
$119.99$119.99
$86.99$86.99
$36.99$36.99
$119.99$119.99
Model No.
BG-GRIND4
BG-GJ
BG-VG
BG-GRIND4
Base Clamps
2 pcs
2 pcs
No
2 pcs
Long Support Arm
Yes
Yes
No
Yes
Platform Table
Yes
Yes
No
Yes
Fingernail Gouge Jig
Yes
No
Yes
Yes
Skew Jig Attachment
Yes
No
No
Yes
This high-performance grinding jig serves as an upgraded grinder table for everyday grinding; replacing the light duty tool rests on your grinder.
It offers even and consistent grinding of your chisels, gouges, and other cutting tools.
Ideal for quick grinding of fingernail profiles on shallow spindle gouges or side grinds on deep fluted bowl gouges. The v-arm holder support your chisels at a constant angle. With Fingernail gouge jig, it allows you upgrade to a three-position tool holder.
The two bases mount under each grinding wheel of your grinder. The locking handle allow you to secure positioning after moving the bases in or out based on your needs.
The platform table can be repositioned in different angles by the adjustable lock lever.
Customers say
Customers find the grinding jig system works well and is well-built. They appreciate the good installation instructions and consider it good value for the cost. They like its sharpening ability, with one customer noting that turning tools sharpen quickly and cleanly.
AI-generated from the text of customer reviews
User Reviews
Be the first to review “BG-GRIND4 4PCS Set Complete Grinding Jig System for Wood Chisels”
You must be logged in to post a review.
There are no reviews yet.